Making Vine Wreaths (2024)

Now that we are just past the Winter Solstice, time for pruning is beginning, which offers the opportunity to make wreaths. In this post, we make a wreath from grape canes, but any long, pliable non-thorny vine material can work -- honeysuckle and wisteria are two that come to mind. You will want a minimum of 2-3 ft. lengths, but 3-4 ft. isbetter. Longer than that and it gets difficult to weave with but requires fewer additions.

Once you have pruned your plant and have some material to work with, here are simple steps to follow for making a circular wreath.

Step 1. Holding the thicker end in your non-weaving hand, bring the vine around forming a circle. Keep in mind that the inner diameter will get a little smaller while the outer diameter will get larger.

Step 2. Working the end of the vine from front to back and up through the center of the circle, make three to four wraps each time around the diameter of the circle. If you are making a larger wreath, you will need more wraps to make it more stable. Work the vine to maintain a nice angle to the wraps while keeping the circle round. If you are using a finer vine such as honeysuckle, you will need to make more wraps around each time.

When coming to the end of a length of vine, tuck it into one of the spaces between interwoven vines, preferably to the back.

Step 3. Begin the next vine about one hand width from the start of the previous vine, tucking the thick end into one of the interwoven spaces on the front so that it is secure before weaving as above. You will probably have to tussle with the form and push down uneven edges on a hard surface to keep it round.

Continue tucking in ends and new beginnings working to keep the weaving balanced and even. The vines are easy to pull out and re-do if needed.

Step 4. There is no set number of vines to use for your wreath, just keep adding and weaving until you have something you like.

If you can't get to making wreaths shortly after pruning but wish to at a later date, that is not a problem. Harder material such as grape canes will need to be soaked for a couple of hours in a tub to soften them. They should be pliable enough to weave without too much breakage. Finer material such as wisteria or honeysuckle needs less time to soak, but would benefit from some soaking to keep the breakage to a minimum.

/span>

Making Vine Wreaths (2024)

FAQs

What vines make good wreaths? ›

In this post, we make a wreath from grape canes, but any long, pliable non-thorny vine material can work -- honeysuckle and wisteria are two that come to mind. You will want a minimum of 2-3 ft. lengths, but 3-4 ft. is better. Longer than that and it gets difficult to weave with but requires fewer additions.

When to make grapevine wreaths? ›

You can cut them in the late summer when they are still green or the early fall when they are brown but not fully hardened yet. If you wait too long the grapevines harden and basically become sticks which are no good for bending.

How to harvest grape vines for wreaths? ›

Harvesting the Vines: Grapevines should be cut anytime after the grapes have been picked, up to first frost. I've found that Virginia Creeper is usually vigorous enough to harvest in mid-summer. Cut long lengths of vine to work with – anything from 3 feet to 10 feet is a workable length.

How do you attach flowers to a vine wreath? ›

With a pan, all you need to do is dip the stem, then insert it into the grapevine network. Glue guns are handy for spot gluing and for intricate work, but for most of the permanent botanical work in a florist shop, a glue pan is likely more efficient. Try to keep a natural bristle brush in the glue pan.

How to make a clematis wreath? ›

Clematis Vine Swing
  1. Manipulate the vine so that it can be woven. ...
  2. Curve the vine into a circle to begin weaving a tiny wreath. ...
  3. Weave the stem end tendrils into the wreath.
  4. For my swinging nest I wove three larger wreaths and one small one. ...
  5. Weave a longer vine through the wreath.
Apr 18, 2018

What are the three types of vines? ›

Why do vines twine in a circular direction? There are actually three different kinds of vines: clingers, tendril-climbers, and twiners.

How long to soak grapevines? ›

Grapevines (Soak in hot water for about 24 hours if the vines are dry, this makes them easier to work with) 24 Gauge Wire (cut into 3-inch strands) Wire Cutters.

What is the fastest growing decorative vine? ›

What is the fastest growing flowering vine? Akebia quinata are one of the fastest growing flowering vines, adding 20 feet to its height every year. If these fast-growing flowering vines are grown in zone 6 or above, they are also evergreen making them a brilliant, permanent addition to the garden.

What can I use instead of a grapevine for a wreath? ›

Aside from grape vines, clematis, willow, wisteria, and honeysuckle are commonly used to make wreaths. As a side note, if you want to skip making the vine wreath altogether, you can buy ready-made ones at most craft stores. Once you've created your wreath, you can decorate it however you like.

What is the best setup for grape vines? ›

Basically, you need a large, open, sunny space with good soil. Grapes need about 50 to 100 square feet per vine if growing vertically on a trellis or arbor. They need about 8 feet between rows if planting horizontally in rows. Plus, seven to eight hours of direct sun each day.

How to make a natural vine wreath? ›

Pull the vines out of the bucket, and start at one end, making a circular coil. Take any side branches and wrap them into the wreath too. Continue wrapping the vines around and over each other until you get the size you want. Allow the wreath to dry.

How do you prepare grape vines for crafts? ›

If the vine has extra pieces growing off of it, keep them because these will add substance to the wreath. While you can work with the star wreath pieces when they are completely dry, a secret technique to making wood pliable for a circle shape is to soak it in water first.

How do you put greenery on a grapevine wreath? ›

Separate greenery bushes into desired sections to easily attach to grapevine wreath. Be sure to count your sections before securing to base so you can evenly space over wreath. Also, don't forget to “fluff” the greenery before placing it in the wreath so that your wreath won't be flat and one dimensional.

How do you make a hop vine wreath? ›

Build a Hop Bine Wreath
  1. STEP 1: SOAK. Load the bines into the bathtub, plug the drain and shower hot water on them until the tub is full. ...
  2. STEP 2: SNIP. Use a pair of scissors to cut the branches off of the main bines. ...
  3. STEP 3: WRAP. ...
  4. STEP 4: REMOVE. ...
  5. STEP 5: CIRCLE. ...
  6. STEP 6: DECORATE.

How do you make a succulent wreath? ›

  1. Step 1: Make Cuttings. Make your cuttings the day before you begin the wreath. ...
  2. Step2: Soak Wreath Form. SONY DSC. ...
  3. Step 3: Insert Succulents. SONY DSC. ...
  4. Step 4: Fill in Entire Form. SONY DSC. ...
  5. Step 5: Secure. SONY DSC. ...
  6. Step 6: Care. Keep your new wreath out of direct sunlight for a week so the cuttings can adjust to their new home.

Top Articles
Latest Posts
Article information

Author: Mr. See Jast

Last Updated:

Views: 6045

Rating: 4.4 / 5 (55 voted)

Reviews: 86% of readers found this page helpful

Author information

Name: Mr. See Jast

Birthday: 1999-07-30

Address: 8409 Megan Mountain, New Mathew, MT 44997-8193

Phone: +5023589614038

Job: Chief Executive

Hobby: Leather crafting, Flag Football, Candle making, Flying, Poi, Gunsmithing, Swimming

Introduction: My name is Mr. See Jast, I am a open, jolly, gorgeous, courageous, inexpensive, friendly, homely person who loves writing and wants to share my knowledge and understanding with you.